Urlload540

• 1Motherboards
• 2Processors
• 3Graphics Cards
  • 3.1AGP
  • 3.2PCI Express
• 4Network Cards

• Install Method: Retail Disc with Boot-132.
• Patches: Audio needs this codec dump and applied using AppleHDAPatcher v1.20.
• What doesn't work: Shutdown/Restart rarely works, and will not wake from sleep.
• Can also follow the IP35-E instruction below(using iAktos 5i)

• Source: iAktos 5i (10.5.5, upgradable to 10.5.6).
• Installs fine on IDE optical drive to a SATA HDD.
• Do install procedure in following order:
• On iAktos 5i (10.5.5) install DVD, check box the following only: cameleon, dsmos, AppleSMIBIOS-28, Stock ACPI modified, APIC Driver, disabler.kext, Intel SATA, JMicron.
• Patch video card as appropriate (OsX86Tools may work okay at this point).
• Update to 10.5.6 with this procedure [1] (follow procedure exactly).
• Audio: works 100% with this patch [2], do this only after 10.5.6 update.
• LAN: works 100% with this patch [3], do this only after 10.5.6 update.
• Use OsX86Tools to enable Quartz Extreme...but don't use OsX86Tools to download & install NVinject, this bricked my machine twice.

Unable to wake from sleep (even with current bios ver. 18). Have not tested PS/2 ports. Needed to install a SATA DVD burner to rip/burn DVD/CD's without getting kernal panic. Also, needed to use the ToH 9.2.0 kernel [4] in order to successfully launch Parallels without kernel panic.

• iAtoks 5i with: PC EFI, Appledecrypt, SMBIOS-EFI, 9.2.0 TOH Kernel, APCI Driver, Disabler.kext, Remove Thermal, Intel AHCI sata, Jmicron, Realtek R1000
• Audio worked with ALC888 driver here [5]
• Used Stationapollo_ICH9 Patch to get sata to work (i used ide HD to install), had to repair permissions, and boot with -f and/or -x till it worked fully.
• Have a NVIDIA GeForce 7300 SE used NVKUSH on iAtoks disk. have full QE and Core support.

• Install Method: iATKOS v4 (didn't work), iDeneb 1.3 10.5.5 (didn't work), Kalyway 10.5.2 w/ TheStevo Patch (didn't work), XxX x86 10.5.5 Leo Install Disc Beta1 (needed to boot DVD with cpus=1 Success!! Latest iATKOS v5i (needed to boot DVD with cpus=1 works)). Success with Voodoo 9.5.0 Kernel.
• BIOS Version: 1.90 (2.10 does not work); Board Revision: 1.0.
• BIOS setup options: CPU FSB Timing set to Manual to fix timer calibration error, Manual DDR RAM Settings, Disabled Serial, Parallel & MIDI Ports, No-Excute Memory Protection = Enabled, HPET Table = Enabled.
• Audio: Realtek ALC888 (with iAtkos PC-EFI V9, worked without patch. Used the ALC888 kext as well for more functionality).
• LAN: VIA Rhine II using VIARhine.kext
• SATA & IDE: SATA onboard but did not test. IDE works fine.
• Optical Drive: LG DVD-Writer works fine.
• Do shutdown, reboot and sleep work? Yes
• VGA card reads as PCI

* Requires modified BIOS (2.0) from: [6]* Used iATKOS 5i* Flawless install. Recognized all 8GB of RAM as well as both cores of my Core 2 Duo E8400.SATA AHCI works with the Intel ICH driver as well as JMicron PATA. Onboard LAN works OOB. Shutdown/reboot functions as it should.

(see notes)

• Install Method: IDeneb 1.3 OSX 10.5.5
• Bios: Set Default
• CPU: Intel Pentium [email protected]
• Ram: 1.5GB DDR
• Video:Nvidia FX5200 128mb
• Audio:AC'97 5.1
• Optical: LG DVD-ROM Drive
• Lan:Realtek PCI LAN 8101L
• IMPORTANT:BEFORE STARTING THE INSTALLATION DISABLE THE LAN IN THE BIOS, AFTER THE INSTALLATION ENABLE IT(The install crash if you don't)
• Patch
  • Audio: AC97 audio
  • Chipset: ICHx fixed
  • Kernel: 9.4.0 stageXNU
• Fix:
  • IOUSBFamilyFix
  • AppleSMBIOS: AppleSMBIOS 800
  • Video: nVidia----- NVinject 0.2.1 128Mb

PC-EFI v9 works without issue.Kernel 9.4.0 stageXNU

No (See Notes)

• Install Method: iATKOS 5i OSX 10.5.5
• Bios: Set Default
• CPU: Intel Celeron D 325 2.5GHz
• Ram: 1.5GB DDR (333 Mhz)
• Video:Nvidia FX5500 256MB
• Audio:AC'97 5.1
• Optical: LG DVD-RAM Drive
• Lan:Realtek 8139
• Patch
  • Bootloader: Chameleon
  • Audio: AC97 audio
  • Chipset: Intel SATA
  • Kernel: 9.5.0 Kernel Voodoo
  • ACPI: APIC Driver
• Fix:
  • IOUSBFamilyFix
  • Video: nVidia -- Titan
  • Network: Realtek 8139

Chameleon + 9.5.0 Kernel Voodoo

No (See Notes)

• VIA P4M800 PRO (north)
• VIA VT8251 (south)

• Realtek ALC653 AC'97 Audio (Not working)
• VIA UniChrome Graphics (untested)
• 'iATKOS v5i' Installed packages
  1. AppleDecrypt
  2. SMBIOS-EFI
  3. AppleSMBIOS netkas
  4. x86 ACPI
  5. Disabler.kext
  6. VIAATA driver
  7. VIA Rhine driver

• EFI V9
• 9.5.0 voodoo
• 9.2.0 ToH

• Realtek RTL8201CL LAN (Via Rhine kext)
• SATA
• IDE
• USB

• Install Method: Kalyway 10.5.1->10.5.3->10.5.5->10.5.6(via software updates)
• BIOS Version: latest
• Realtek ALC883 working via AsaliaAudio(output)->AppleHDA.kext (patch at link).
• Attansic Gigabit (kext included)
• SATA: ICH9 controller works fine(kext included).
• PATA: Marvell 6111 controller works fine(kext included).
• USB: all working

• Install Method:BOOT 123 CD IMAGE (link), RETAIL 10.5.4 DVD
• 9.5.0 vanilla kernel
• BIOS Version: 812
• MAC OS X 10.5.6 COMBO UPDATE (link)
• DSDT Patcher GUI (link)
• UNIVERSAL OSx86 INSTALLER (link)
• Audio AD1988B 8 - Channel High Definition Audio CODEC (link)
• Wireless P5K Deluxe/WiFi-AP (link) BUGGY CAUSES RANDOM PANICS..DISBALE AND USE ONBOARD ETHERNET
• Fix Orange Drives AHCIFixv2 (link)
• Fix Sleep with AppleUSBUHCI328.kext.zip kext (link)
• Kext Pack Installer from this guide (file)
• Installation Instructions:
  1. Boot with 'BOOT 123' CD, After loading press 'F8' then 'ESC'
  2. Replace disk with Retail DVD and press 'Enter' twice.....long boot time...be patient!
  3. Open Disk Utilities and setup your install disk as 'GUID'
  4. Selece printer driver in the install options and continue install...
  5. You will get an error when the install completes...Ignore it and reboot.
  6. Boot with 'BOOT 123' CD, After loading press 'F8' then 'ESC'
  7. Enter the number '80' if OSX installed on the first drive, or enter '81' if installed on the second drive and 'Enter'. This is the order your motherboard boots your hard disks.
  8. You will see the initial video for OSX
  9. Run the 10.5.6 Combo Update<Proxy-Connection: keep-alive

Cache-Control: max-age=0

...DO NOT REBOOT...JUST MINIMIZE</b>

• 1. Run the 'DSDT Patcher GUI'...Select 'MAC OS X', Select your boot drive, click 'Run DSDT Patcher'
  2. Run the 'Universal OSx86 Installer' and choose the following
     1. Choose the hard drive to apply to
     2. Set the boot time....only if you care to have the bootloader count down
     3. Check 'Apply Kext Package'
     4. Set Native Boot Resolution (mine is 1920x1200)
     5. Check 'Install PC_EFI_V9 Option...VERY IMPORTANT
     6. Check 'Apply Ethernet EFI String'
     7. Check 'Apply EFI String for Video Card' (Select Your Model)
     8. Press 'Install'
  3. Install 'P5K-SE_10.5.6.pkg'
  4. Install 'Taruga_AD1988b_rev3_Installer' Sound
  5. Install '87_Mac10.4_v1309' Wireless...I wouldn't if I were you. Will make your system unstable.
  6. Reboot...W/Out 'BOOT 123'
  7. Run the 'Universal OSx86 Installer' again and this time only choose the following
     1. Check 'Apply Ethernet EFI String'
     2. Check 'Apply EFI String for Video Card' (Select Your Model)
     3. Check 'Install Custom Kexts from HD' (Browse to kexts and select)
     4. Press 'Install'
     5. Reboot
  8. Open 'OSx86Tools' and click 'Enable/Disable Quartz GL' to verify if enabled...if not, enable.
  9. Goto 'System Preferences, Sound, Output and select 'Line Out'
  10. Follow link above to fix orange drive icons if it bothers you. It's only cosmetic.
  11. Run Update and update everything
• DONE

NOTE: Here is a zip archive of all the files you will need including my BIOS SETTINGS. You still have to download the combo update 10.5.6, Wireless driver, and purchase Leopard Retail 10.5.4.

• Install Method: Idened 10.5.5
• AD1988B Audio: works
• Marvell 88E8056 LAN: works
• Realtek RTL8110SC LAN: works
• Onboard WiFi: Realtek driver
• ICH9R SATA: works
• e-SATA: working, but set AHCI mode in Bios
• Jmicron PATA: not tested
• USB: Works

• Instalation method: iDeneb 1.3
• P695 works OOTB
• ICH8, JMicron - works with patches: ICHx, JMicron (from iDeneb DVD)
• SATA Devices - works, IDE Devices - unknown
• LAN: Marvell 88E8001 - works with patch: Skge Marvell (from iDeneb DVD)
• Audio: AD1988A - unknown
• USB - works OOTB (to use front ports disable USB Legacy in BIOS)
• Onboard GPU: GMA X3000 - no CI/QE, posible resolution change with patched X3100 kext (not included in iDeneb DVD)

Onboard GPU not fully working.

• Installation method: Kalyway 10.5.1 Vanilla Kernel + kalyway 10.5.2 combo update + Kalyway 10.5.3 combo update + 10.5.4,10.5.5 original package combo update with this guide: http://netkas.org/?p=50
• SATA: works
• IDE: works
• LAN: Works OTB
• Audio: Works OTB.
• Wireless: Included patch makes some problem , resolved with new RTL8187L driver from Realtek site
• USB: All ports works OTB
• Firewire: Works OTB

• EFI V9
• Vanilla Kernel

• Installation method: iATKOS i5 (10.5.5)
• Intel 945GC (A2): works OOTB
• ICH7: works OOTB.

(Selected ICHx AHCI kexts during install.)

• SATA: works
• IDE: works
• LAN: works OOTB with this kext [7]

(Used a cheap Realtek 8139C PCI, works OOTB)

• Audio: Works OOTB.

(Select ALC883 during install (or try ALC662). Shows up in System Preferences as HDAudio, but not in System Profiler. Two channel stereo out works, no input options available though.)

• USB: All ports work OOTB
• Onboard GPU: Use the vanilla 10.5.6 GMA950 kexts and this patched DSDT (Core based CPU required.)
• Power: Shutdown, reboot, and sleep work 100%

(Hint: Switch the PS2_USBPWR jumper on the motherboard to enable sleep.)

• EFI V9
• 9.5.0 voodoo
• 9.2.0 ToH
• Vanilla untested

• Installation method: iDeneb 10.5.5 v1.3 (10.5.5)
• SATA work OOB (Selected VIAATA kexts during install.)
• IDE: works
• LAN: works (Used Attansic L1 kext, get it here)
• Audio: Works. (Select Azalia during install. Only 2-channels)
• USB: All ports work OOTB
• Power: Shutdown, reboot, and sleep work 100%

• EFI V9
• Kernel 9.5.0
• Vanilla untested

• Installation method: iDeneb 10.5.5 v1.3 (10.5.5): Kernel 9.4.0; Fixes: ICHx;
• Pentium 4, 2.4 GHz, SSE2, Northwood, 1GB RAM, 80GB Harddrive (20GB HFS, 60GB Fat32, had to set 1. partition active)
• IDE: works
• LAN: not tested
• onboard C-Media works with CMI8738PCIAudioDriver.kext
• USB: OK
• Power: Shutdown, reboot
• Graphics: ATI Radeon 9200 - in VESA Mode 1280x1024
• AppleSMBIOS netkas (default)

• Kernel 9.4.0

• Installation method: iDeneb 10.5.5 v1.3 (10.5.5): Kernel 9.4.0 SageXnu
• Boot in safe mode (-x) without any LAN, Audio, Video drivers.
• SATA: Works, with patched NforceATA drivers
• IDE: works
• LAN: Works latest nForceLan drivers
• Audio works with ALC883
• USB: OK
• Power: Shutdown, reboot

• Kernel 9.4.0SageXnu, 9.5.0 Not tested

• install using iAtkos i5, no patches needed

• Installation method: iDeneb 10.5.5 v1.3 (10.5.5): Kernel 9.4.0 SageXnu
• SATA: not tested
• IDE: works
• LAN: Works with skge Marvell selected from the installation dvd
• Audio works with AC97 AUDIO selected from the installation dvd
• USB: it works but non perfectly (iousbfamily kext)
• Power: Shutdown, reboot ,all work

• Kernel 9.4.0SageXnu, 9.5.0 Not tested

Installed using iDeneb v1.3 10.5.5 using only the following:

• Select AC'97o
  
• Select JMicron ATA
  
• Select Intel Chipset
  
• Select Kernel 9.4.0 Stage XNU
  
• Used NVinjectGO for Geforce 6200 AGP (Normal NVinject Wouldnt Work use titan.kext also and download Nvidia Universal Installer.mpkg install all and reboot QE!
  
• Select any other drivers that are available that may go with your hardware.
  Install and enjoy! VERY easy install.
  

• Kernel 9.4.0 Stage XNU tested

• Intel Celeron 2.0 Ghz
  
• Onboard ethernet works
  
• PCI slots work Sound Blaster Pro (Shows up as AC'97)
  
• USB works
  
• IDE works
  
• Audio works!
  
• Sleep, Shut down, Restart work
  

• EFI v9
• Kernel 9.2.0
• Kernel 9.5.0 voodoo (ocasional freeze up)

• Install Method: iAtkos 10.5.5
• Audio: Realtek ALC655, (Working great with patch from DVD)
• LAN: Realtek 8100c, (Working great with patch from DVD)
• SATA & IDE: Odd shutdowns during intense disk activity with SATA enabled. Used IDE hard drive and disabled SATA in the BIOS.
• Optical Drive: Philips DVD+/-RW 8631
• Shutdown and reboot work great, no video on resume from sleep. (May be an issue with my install.)
• Working great with Celeron D 3.33ghz and 7300GT graphics. May try other drivers/kernels in the future to try to fix the SATA issue.

Installed using iDeneb v1.3 10.5.5 using only the following:

• Select AMD patch
  
• Select ALC 883 Audio
  
• Select JMicron ATA
  
• Select VIA-SB Chipset
  
• Select Kernel 9.4.0 Stage XNU
  
• Select Firewire Remove
  
• I selected also X1300-X1550 Graphics drivers since I have a PCIex16 ATI X1550 card, works great!
  
• Select any other drivers that are available that may go with your hardware.
  Install and enjoy! VERY easy install.
  

• Kernel 9.4.0 Stage XNU tested (didn't try others since this one worked on first try

• Recognizes the Athlon 64 X2 4800+ as 2.5Ghz Unknown
  
• Onboard ethernet works
  
• PCI slots work (recognized my D-Link DWA Extreme N wireless card OOB)
  
• USB works
  
• SATA works
  
• Audio works!
  
• Sleep, Shut down, Restart work
  

• AHCI enabled, JMicron enabled
• SATA DVD & HDD drives

Installation:

• Vanilla 10.5.0 updated to 10.5.5
• Netkas v9
• Kexts & patches:
  • Used LTL's Guide including LTL's pre-patched AppleHDA.kext for sound (ALC889A)

Sound Output Configuration: Select Internal Speakers in System Preferences for line out (sound output mapping issue?)

• Kernel section: SpeedStep (Intel/AMD/SSE2/SSE3);
• Chipset section checked: ICHx Fixed
• Fix section checked: ACPI-Fix; Cpus=1-Fix.

Hardware:

• SATA DVD & HDD drives
• onboard VGA card
• onboard sound card (disabled in bios)
• onboard Ethernet card (disabled in bios)
• PCI phir. (enabled in bios)
• USB mouse
• Ethenet PCI RTL8139D
• Firewire PCI 400 VIA VT 6307
• GF 8400GS 256MB

NB: install system with PCI cards but without GF8400gs, then during 1 restart take out the PCI Ethernet card, then register system > go to network settings, look at hardware: Firewire there is!!! andmake the second restart, during the 2 rr. put in motherboard Ethernet card, when you are in system, go to network settings, there must be available Your ethernet and FireWire both.Then downlaod kext for GF8XXX, install with kexthelper, and make 3rd restart. During the restart put your VGA GF8400 card in, and reconnect vga cable from onboard intel vga to external GF8400. I hope you will have success!

• Kernel section: SpeedStep (Intel/AMD/SSE2/SSE3);
• Chipset section checked: None
• Fix section checked: None.

Hardware:

• SATA DVD & HDD drives
• X1950 Pro (Asus)
• onboard sound (disabled in bios)
• onboard Ethernet (disabled in bios)
• USB Keyboard
• USB mouse
• Enabled AMD cool and quiet
• SATA set to AHCI

• Kernel section: Kabyl 64bit (Intel/AMD/SSE2/SSE3);
• Chipset section checked: None
• Fix section checked: None.

Hardware:

• SATA DVD & HDD drives
• XFX HD5770 (does'nt work OOB, use GMA Drivers while install)
• onboard sound (not working OOB, use AppleHDA.kext)
• M-Audio Delta 192 (not working OOB, use Envy24HT)
• onboard Ethernet (works OOB)
• USB Keyboard
• USB mouse
• SATA set to AHCI

• Intel Dual Core Pentium, 2.2 GHz

• Chipset - Intel ICHx (iDeneb 10.5.5)
• Audio - No Selection
• Ethernet - No Selection (Works Fine)
• SMBios - Patch 667 (iDeneb 10.5.5)

• Method of Install: OSX86 iDeneb 10.5.5

• Did not test onboard video
• used nVidia GeForce 8600GT 512MB - NvInjector 512mb (iDeneb 10.5.5)
• Patch audio with package from (iPC 10.5.6 Final - ALC888)

1. Audio Sigmatel STAC9274D Working with Apple HDA Patcher 1.16 and STAC9274D codec dump available at insanelymac forums
2. LAN Intel Gigabit Ethernet working out of box
3. USB working out of box for all ports and all devices
4. FireWire works out of box
5. IDE working, SATA controller working in AHCI mode, Native, detected as ESB2 or Unknown AHCI controller
6. According to the IO Registry, some devices are not working, but everything works fine
7. Optical drives, harddrives, ram and all pci slots work
8. Installs from SATA DVD Drive

1. Audio ALC888S Working with Apple azalia In-built Codec. No need to install any audio patch.(If in iAktos 5i)
2. LAN Intel® 82566DC Gigabit Ethernet Controller needed Intel82566MM.kext.
3. Intel E7200 @ 2.53Ghz Detected as Core2Duo @2.53Ghz unknown.
4. USB,FireWire Working OOB.
5. SATA Set to AHCI. Working flawlessly.
6. DVD drive On SATA is ready For installation and USE.
7. PATA working.
8. XFX 8600GT XXX work.With Nvkush and Efi-Strings.

(i am Not Getting 1366x768 in My 16' Widescreen Monitor.)

1. iAktos 5i vanilla 9.5,Voodoo 9.5,fassl 9.5 kernel not working Choose 9.2 Toh kernel or Patch iDeneb 1.3 vanilla 9.5 kernel.

1. Audio: Realtek AC97 works w/o patch
2. LAN: Realtek RTL8139 -Select RTL8139 from the List
3. Intel Pentium D 805 2.66 GHZ- Select SMBIOS'S DRIVERS - Apple Imac Driver
4. Kernel -9.5.0 Voodoo
5. ACPI - APCI option
6. Disabler
7. SATA- Intel SATA option
8. VGA - Nvidia FX5500 256 MB- Titan Driver-1920x1080p resolution
9. BootLoader- Chameleon v1

• Install Method: Kalyway 10.5.2->10.5.3->10.5.4->10.5.5 (via software updates + shell script)

Everything is working fine, except sleep, all the PS2 audio in/out plugs and AirPort (using USBWirelessUtility instead).

• So, this little one was a right bugger to deal with, but i have got this working, infact im writing this on it now.

So what we have here is OEM Board from MSI its a generic brand, but its usually found in Medion or Advent Desktop PCs.So how to install? Simple, Download the iDenib OS X 10.5.5 distro, burn it, plop it in the drive, run the install in verbose mode '-v'when you hit the installer, prepare your HDD, i have XP and 7 Triple booted, with dual bootloading just in case ;), once your in your customise settings....Choose Azailia Audio, Your GFX, this is running Nvidia 8500GT 256MB, with 1GB DDR SDRAM, P4 HT 550 3.4GHz, dont choose any smbios, choose ich for chipset, choose viarhine for onboard ethernet, and for the rest, have a tinker around, oh and make sure to enable in the bios usb 1.1 mode or otherwise your mouse wont work, and even thats buggy at times, if you dont click the buttons the mouse will play dead so you will have to do a hard reset if you havent got mac hardware plugged in that is, if there is anything else, i will update it, cause ive spent 6 hours getting this working, and my god its a pain in the butt!, but yeah if you have one of these generic boards or even have an advent, swap your gpu for the nvidia, cause you wont get it up and running with the standard ati radeon x600 pro that ships with the mbo.

• CPU: Core 2 Quad Q9550 2.83Ghz
• Chipset: Intel P35 + ICH9R
• Memory: 4 x 2G Ram
• SATA: DVD & HD
• Video Card: Zotac Gforce GT5250 1G DDR3 (Nvidia)
• Audio: Realtek ALC888 only 2 channel works
• USB works
• Firewire works
• ESATA not tested
• LAN: Marvell 88E8056 works
• Sleep works
• Restart works
• Shutdown works

• Installed with the following checked in iDeneb 10.5.5
  • Audio: ACL888
  • Chipset: ICHx
  • Video: Nvidia 1G

• Used iDeneb v1.3 with NVInject 256 driver.
• DVI out not tested (do not have cable or compatible monitor)

• NVInject, NVDarwin.
• Needed to use DVI to D-Sub VGA adapter to get monitor resolutions recognized on VGA analog input.
• DVI out to DVI input worked flawlessly.

• NVInject, NVDarwin. Kalyway 10.5.2 Supports QE iDeneb 10.5.5 hasnt (yet)
• DVI and VGA And Dual Monitor worked flawlessly.

• NVInject.
• Have not tested VGA, only have DVI monitors.
• DVI out to DVI input worked flawlessly.

• Used Natit, haven't tried others.
• VGA works perfectly.

DVI don't work properly

DVI work (no NVCAP etc. needed)

(Id. 0422)

DVI needs NVCAP in info.plist.NVCAP to try:BAAAAAAAAgAAAAAHAAAAAA / BAAAAAAABQAAAAAHAAAAAA / BAAAAAAABgAAAAAHAAAAAA

CT4670

Input still dosen't work